W6100 MKR Ethernet Shield

Overview

ARM mbed compatible operation

Arduino Pin-compatible

Arduino MKR Series (Only MKR Etherent Shield)

Ethernet (W6100 Hardwired TCP/IP chip)

W6100 Ethernet shield is designed using the WIZnet W6100 chip. Please click the link for the further information about W6100. 

The best advantage of the W6100 (MKR-)Ethernet Shield is that it supports IPv6. It supports both 3.3V & 5V. 

This Ethernet Shield is compatible with Arduino and ARM mbed Platform.

W6100 suits users in need of stable Internet Connectivity best, using a single chip to implement TCP/IP Dual Stack, 10/100 

Ethernet MAC and PHY. Hardwired TCP/IP Stack supports TCP, UDP, IPv4, IPv6, ICMP, ARP, IGMP, and PPPoE etc which has 

been proven through various Applications over many years.

Features

• Support Hardwired TCP/IP Protocols : TCP, UDP, IPv6, IPv4, ICMPv6, ICMPv4, IGMP, MLDv1, ARP, PPPoE
• Support IPv4/IPv6 Dual Stack
• Support 8 independent SOCKETs simultaneously with 32KB Memory
• Support SOCKET-less Command: ARP, PING, ICMPv6(PING, ARP,DAD,NA,RS) Command for IPv6 Auto-configuration& Network Monitoring
• Support Ethernet Power Down Mode & System Clock Switching for power save
• Support Wake on LAN over UDP
• Support Serial & Parallel Host Interface: High Speed SPI(MODE 0/3), System Bus with 2 Address signal & 8bit Data
• Internal 16Kbytes Memory for TX/ RX Buffers
• 10BaseT / 10BaseTe / 100BaseTX Ethernet PHY Integrated
• Support Auto Negotiation (Full and half duplex, 10 and 100-based )
• Support Auto-MDIX only on Auto-Negotiation Mode
• Not support IP Fragmentation
• 3V operation with 5V I/O signal tolerance
• Network Indicator LEDs (Full/Half Duplex, Link, 10/100 Speed, Active)

Guide Docs

W6100 Ethernet Shield

Overview

W6100 Ethernet Shield is based on W6100. For more information about W6100, please visit W6100 Datasheet. This Ethernet Shield can be 

used on boards with an Arduino Pin Header Form factor. W6100 suits users in need of stable Internet Connectivity best, using a single chip to 

implement TCP/IP Dual Stack, 10/100 Ethernet MAC and PHY. Hardwired TCP/IP Stack supports TCP, UDP, IPv4, IPv6, ICMP, ARP, IGMP, 

and PPPoE etc which has been proven through various Applications over many years.

• Arduino Platform
• Others Arduino Pin-Compatible Boards
• ARM mbed Platform

Features

• Operation Voltage DC5V or DC3.3V
• Signals (SPI) Voltage 3.3V
• Included W6100 of WIZnet
• SPI Interface
• 10/100 Ethernet PHY embedded
• Hardware TCP/IP Protocols - TCP, UDP, IPv6, IPv4, ICMPv6, ICMPv4, IGMP, MLDv1, ARP, PPPoE
• Support IPv4/IPv6 Dual Stack
• Support 8 independent SOCKETs simultaneously with 32KB Memory
• Support SOCKET-less Command: ARP, PING, ICMPv6(PING, ARP, DAD, NA, RS) Command for IPv6 Auto-configuration& Network Monitoring
• Support Auto Negotiation
• Full / Half Duplex
• 10/ 100 Based
• Support Micro SD Card slot for storage
• Low height RJ45

Technical Support

W6100-EVB

Key Features

• 32bit ARM Cortex-M3 based evaluation board for W6100S chip
• Hardware pin-compatible with Arduino Uno Rev.3
• Supported 2 Push button switch (SW), 1 x RGB LED
• Supported 1-Port Ethernet Connector / USB-micro Type B connector
• Supported ISP & SWD Interface
• Provides various application code – Loopback, DHCP, DNS.

Hardware Specification

• MCU: STM32F103VCT6 Cortex-M3 (Running at up to maximum 72MHz, 256 or 512KB Flash, 64KB SRAM)
• Ethernet: W6100S (WIZnet Hardwired TCP/IP)
• Power: 5V DC Power
• Expansion I/O: 80 GPIOs (Include analog Peripheral using 12bit ADC)
• RJ-45: 1-channel 10/100 Base-TX RJ-45 with Transformer (57-00013QL11-1 / UDE)
• USB: USB Micro-B Type (On-board USB-to-UART IC, USB BUS Power / CP2104) – Use to debug
• On-board User I/F: 2xPush button switch, 1xRGB LED
• Dimension (mm): 90 (L) x 80 (W) x 15(H)

Materials in WIZwiki